Apatent application was made in 1981 for the earth shattering invention of "the original – LUX ELEMENTS® hard foam support ELEMENT".
The construction panel for walls and floors LUX ELEMENTS®-ELEMENT
The installation cladding LUX ELEMENTS®-TEC
Bath surrounds LUX ELEMENTS®-TOP
The washstands LUX ELEMENTS LAVADO®
Point drainage LUX ELEMENTS TUB®
Linear drainage LUX ELEMENTS TUB-LINE®
Wellness LUX ELEMENTS®-RELAX
Prefabricated room constructions LUX ELEMENTS®-MODUL
The decorative elements LUX ELEMENTS®-DECO
Individual room constructions LUX ELEMENTS®-CONCEPT
The tried and tested accessories are fully harmonised for processing ELEMENT. Specially developed adhesives and mortars, sealing tapes, mounting angles and plugs ensure problem-free processing.
Fastening sets and dowels LUX ELEMENTS®-FIX
Adhesives LUX ELEMENTS COL®
Sealing filler and sealing tapes LUX ELEMENTS®-DRY
Reinforce LUX ELEMENTS ARM®
Mounting aids LUX ELEMENTS MONT®
LUX ELEMENTS®-...-PLUS Individual, special manufacture for each product group
In addition to standard products, also individually tailored and specially manufactured products are available for the products groups listed under the designation ‘PLUS‘.
Sizes, shapes, thicknesses etc., that deviate from standard features can be inquired from LUX ELEMENTS. After successful verification of implementation possibility at LUX ELEMENTS an appropriate offer will be prepared. Once an order is placed, it will be manufactured and delivered accordingly.
Overview of All Issues
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-Opladen+49 (0) 21 71/ 72 12 - 0 (tel)+49 (0) 21 71/ 72 12 40 (fax)
Prosol Distribution Inc. 165 Rue Deslauriers H4N 2S4 St-Laurent, Québec 001 514 745 1212 (tel) 001 514 745 1215 (fax) firstname.lastname@example.org http://www.prosol.ca/
Current trade fair dates
Check subsurface for load-bearing capacity, remove the separating layers, check suction performance. If required, free from dust, premoisten and prime.
If ELEMENT-EL Baby 4 is used, always apply the fixing adhesive COL-AK over the full surface using a toothed trowel. This technique is also possible for thicker panels, depending on the substrate.
When using ELEMENT-EL ≥ 6 mm, apply the fixing adhesive COL-AK pointwise on one side using dots of adhesive (8 – 10 pcs. per m2). Before applying adhesive pre-pierce the holes for the hammer fix plugs FIX-FID or FIX-KSD.
Position the ELEMENT construction panels at the top edge of the old tiling (knock off obstructive plaster clots before beginning, if necessary) and press to the wall.
Press on with the level and spirit level and align vertically and flush with the old tiling. Also pay attention to the horizontal alignment of the ELEMENT construction panels to one another!
Dowel after approx 3 hours. Select the correct dowel pins or fastening set to correspond with the existing masonry and plaster thickness. Pay attention to water and power lines! We recommend 6–8 dowels per m2. TIP: Pre-drill dowel holes
Reinforce the transition from the ELEMENT to the old tiling with glass fibre reinforcement strips ARM-100 SK.
Level out the glass fibre reinforcement strips, element joints and dowel pin heads with COL-AK. The surface is now ready for tiling. Further requirements (e.g. sealing for wet loads) must be taken into consideration in accordance with national directives.
© 2019 All rights reserved. We reserve the right to make technical changes.Status: Sep 02,2019
Prosol Distribution Inc.
165 Rue Deslauriers
H4N 2S4 St-Laurent, Québec
001 514 745 1212 (tel)
001 514 745 1215 (fax)