Apatent application was made in 1981 for the earth shattering invention of "the original – LUX ELEMENTS® hard foam support ELEMENT".
The construction panel for walls and floors LUX ELEMENTS®-ELEMENT
The installation cladding LUX ELEMENTS®-TEC
Bath surrounds LUX ELEMENTS®-TOP
The washstands LUX ELEMENTS LAVADO®
Point drainage LUX ELEMENTS TUB®
Linear drainage LUX ELEMENTS TUB-LINE®
Wellness LUX ELEMENTS®-RELAX
Prefabricated room constructions LUX ELEMENTS®-MODUL
The decorative elements LUX ELEMENTS®-DECO
Individual room constructions LUX ELEMENTS®-CONCEPT
The tried and tested accessories are fully harmonised for processing ELEMENT. Specially developed adhesives and mortars, sealing tapes, mounting angles and plugs ensure problem-free processing.
Fastening sets and dowels LUX ELEMENTS®-FIX
Adhesives LUX ELEMENTS COL®
Sealing filler and sealing tapes LUX ELEMENTS®-DRY
Reinforce LUX ELEMENTS ARM®
Mounting aids LUX ELEMENTS MONT®
LUX ELEMENTS®-...-PLUS Individual, special manufacture for each product group
In addition to standard products, also individually tailored and specially manufactured products are available for the products groups listed under the designation ‘PLUS‘.
Sizes, shapes, thicknesses etc., that deviate from standard features can be inquired from LUX ELEMENTS. After successful verification of implementation possibility at LUX ELEMENTS an appropriate offer will be prepared. Once an order is placed, it will be manufactured and delivered accordingly.
Overview of All Issues
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-Opladen+49 (0) 21 71/ 72 12 - 0 (tel)+49 (0) 21 71/ 72 12 40 (fax)
Prosol Distribution Inc. 165 Rue Deslauriers H4N 2S4 St-Laurent, Québec 001 514 745 1212 (tel) 001 514 745 1215 (fax) firstname.lastname@example.org http://www.prosol.ca/
Current trade fair dates
Glue the cut-to-size ELEMENTS-EL 50 to the wall with COL-AK such that they can be vertically and horizontally aligned.
The spacing of the cut ELEMENT component parts should be between 30 – 40 cm · 11 13/16" à 15 3/4".
Apply COL-AK to the face end of the levelling construction and glue on correspondingly cut and notched ELEMENT-EL 20 in transverse position.
Glue the individual ELEMENTS-EL 20 by applying adhesive to the edges an joints. Be sure to observe the vertical and horizontal alignment of the ELEMENT construction panels!
Additional fixation with special screw plugs FIX-SD 80.
NOTE: We recommend the pre-piercing of the dowel holes with a cross slot screwdriver.
The levelling construction can take place at full room height or with a shelf above the installations. ELEMENT-EL 20 is suitable for the top cover.
All element joints and transitions are to be reinforced with ARM-100 SK glass fibre reinforcement strips. Then level out the element joints using COL-AK
It must be observed that, in the areas in which sanitary articles such as e.g. washbasins or WCs are later to be suspended and installed, the ELEMENT construction panels are to be glued over the full surface if possible – due to the high pressure absorption. According to the manufacturer’s instructions the load-bearing frames of the suspended WCs should be lined with bricks or planked with wooden boards to avoid torsion.
© 2019 All rights reserved. We reserve the right to make technical changes.Status: Sep 02,2019
Prosol Distribution Inc.
165 Rue Deslauriers
H4N 2S4 St-Laurent, Québec
001 514 745 1212 (tel)
001 514 745 1215 (fax)