Apatent application was made in 1981 for the earth shattering invention of "the original – LUX ELEMENTS® hard foam support ELEMENT".
The construction panel for walls and floors LUX ELEMENTS®-ELEMENT
The installation cladding LUX ELEMENTS®-TEC
Bath surrounds LUX ELEMENTS®-TOP
The washstands LUX ELEMENTS LAVADO®
Point drainage LUX ELEMENTS TUB®
Linear drainage LUX ELEMENTS TUB-LINE®
Wellness LUX ELEMENTS®-RELAX
Prefabricated room constructions LUX ELEMENTS®-MODUL
The decorative elements LUX ELEMENTS®-DECO
Individual room constructions LUX ELEMENTS®-CONCEPT
The tried and tested accessories are fully harmonised for processing ELEMENT. Specially developed adhesives and mortars, sealing tapes, mounting angles and plugs ensure problem-free processing.
Fastening sets and dowels LUX ELEMENTS®-FIX
Adhesives LUX ELEMENTS COL®
Sealing filler and sealing tapes LUX ELEMENTS®-DRY
Reinforce LUX ELEMENTS ARM®
Mounting aids LUX ELEMENTS MONT®
LUX ELEMENTS®-...-PLUS Individual, special manufacture for each product group
In addition to standard products, also individually tailored and specially manufactured products are available for the products groups listed under the designation ‘PLUS‘.
Sizes, shapes, thicknesses etc., that deviate from standard features can be inquired from LUX ELEMENTS. After successful verification of implementation possibility at LUX ELEMENTS an appropriate offer will be prepared. Once an order is placed, it will be manufactured and delivered accordingly.
Overview of All Issues
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-Opladen+49 (0) 21 71/ 72 12 - 0 (tel)+49 (0) 21 71/ 72 12 40 (fax)
Prosol Distribution Inc. 165 Rue Deslauriers H4N 2S4 St-Laurent, Québec 001 514 745 1212 (tel) 001 514 745 1215 (fax) firstname.lastname@example.org http://www.prosol.ca/
Current trade fair dates
The following processing information apply to all panel thicknesses of the slit ELEMENT construction panels, not only for the vertically slit but also for the horizontally slit variant. For information regarding bending radii and technical details.
Carrying of the panels in bent condition is recommended, whereby the slit side should face inwards.
When working with slit ELEMENT construction panels, the adhesive COL-AK should be applied to the inside, meaning the slit side.
The oozing out of a little adhesive when picking up and bending the slit ELEMENT construction panels is normal.
Bending – Bending should generally be effected on the slit side. The smooth outer side is suitable for tiling. If bending in two directions is necessary, two parts can be pre-bent and glued with COL-MK.
Bending of the same ELEMENT construction panel in two directions is possible. One part is bent with the slit facing inwards and one part with the slit facing outwards.
In those cases where the bending is on the outside, the slits are afterwards filled and levelled out with COL-AK.
Often a pre-fabricated template can facilitate the shaping of the slit hard foam support elements. Cut out suitable templates from residual material and place the slit construction panel round this shape with the slits facing inwards.
Clamp in and fix the shaped part with lashing straps.
MONT-U profiles can be used for stabilising in case of two bent elements being positioned on top of or next to one another. The lashing straps must then be laid vertically and horizontally. Bonding takes place with COL-AK.
Bed in reinforcement fabric ARM 600 on the inside.
Levelling out – Finally level out the reinforcement fabric with COL-AK and allow to dry.
© 2019 All rights reserved. We reserve the right to make technical changes.Status: Sep 02,2019
Prosol Distribution Inc.
165 Rue Deslauriers
H4N 2S4 St-Laurent, Québec
001 514 745 1212 (tel)
001 514 745 1215 (fax)