Apatent application was made in 1981 for the earth shattering invention of "the original – LUX ELEMENTS® hard foam support ELEMENT".
The construction panel for walls and floors LUX ELEMENTS®-ELEMENT
Construction panel for underfloor heating LUX ELEMENTS®-FLOOR
The installation cladding LUX ELEMENTS®-TEC
Bath surrounds LUX ELEMENTS®-TOP
The washstands LUX ELEMENTS®-LAVADO
Point drainage LUX ELEMENTS TUB®
Linear drainage LUX ELEMENTS TUB-LINE®
Modular room constructions LUX ELEMENTS®-MODUL-ROOM
Individual room constructions LUX ELEMENTS®-CONCEPT
Individual relaxation and distraction LUX ELEMENTS®-RELAX
The decorative elements LUX ELEMENTS®-DECO
The tried and tested accessories are fully harmonised for processing ELEMENT. Specially developed adhesives and mortars, sealing tapes, mounting angles and plugs ensure problem-free processing.
Fastening set and dowels LUX ELEMENTS®-FIX
Technical fixtures, Heating, Lighting and Sound LUX ELEMENTS®-ADD
Adhesives LUX ELEMENTS COL®
Sealing filler and sealing tapes LUX ELEMENTS®-DRY
Reinforce LUX ELEMENTS ARM®
Mounting aids LUX ELEMENTS MONT®
LUX ELEMENTS®-...-PLUS Individual, special manufacture for each product group
In addition to standard products, also individually tailored and specially manufactured products are available for the products groups listed under the designation ‘PLUS‘.
Sizes, shapes, thicknesses etc., that deviate from standard features can be inquired from LUX ELEMENTS. After successful verification of implementation possibility at LUX ELEMENTS an appropriate offer will be prepared. Once an order is placed, it will be manufactured and delivered accordingly.
Overview of All Issues
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-OpladenTelefon +49 (0) 21 71/ 72 12 - 0Telefax +49 (0) 21 71/ 72 12 40
Construction & design
The shorter Baby construction panels from ELEMENT-EL Baby 10 are suitable for this application.
Irregularities must be compensated using levelling filler. Do not forget the edge insulation strips. Allow the ELEMENT panels to adapt to ambient conditions such as temperature and humidity prior to installation.
The substrate must be load-bearing and vibration-free.
After preparation of the substrate, stick edge insulation strips circumferentially round all wall-floor connections.
Apply COL-AK fixing adhesive with a toothed trowel (depending on the substrate, at least 6 mm) to evenly cover the surface.
The ELEMENT panels are positioned close together in bond and pressed into the adhesive layer.
Dot laying is possible from EL 30. The spacing of the mortar dots should be approx. 20 cm.
Reinforce ELEMENT joints with ARM-100 SK ...
... and level out with COL-AK. Use the fluidised thin bed adhesive COL-FBK or COL-FLEX for the cavity-free installation of tiles.
NOTE: When applying in damp or wet rooms it is necessary to use an additional LUX ELEMENTS®-DRY-ASK or DRY-DF sealing in conjunction with ceramic coverings. Use the fluidised thin bed adhesive COL-FBK or COL-FLEX for the cavity-free installation of tiles.
A total pressure load of 0,1 N/mm² must not be exceeded. When using for higher loads such as transport traffic, rack systems etc., please contact the LUX ELEMENTS technical department.
Also suitable for heating systems due to continuous temperature resistance up to +75°.
© 2023 All rights reserved. We reserve the right to make technical changes.Status: Jan 18,2023
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-OpladenGermanyTelefon +49 (0) 21 71/ 72 12 - 0Telefax +49 (0) 21 71/ 72 12 40